Q1.
What is the primary purpose of process control?
A. Automate production processes
B. Ensure final product quality
C. Optimize production efficiency
D. Monitor and regulate process variables
📘 View Explanation
Correct Answer:
D
Process control monitors and regulates variables to maintain desired output.
Q2.
Which of the following term correctly represents transient nature of a process?
A. Stability
B. Dynamic state
C. Steady state
D. Equilibrium
📘 View Explanation
Correct Answer:
B
A dynamic state represents the transient nature of a process where system variables change with time. In this condition, parameters such as temperature, pressure, or flow rate are continuously varying before reaching stability. Dynamic behavior is important in engineering and industrial systems because it helps analyze how processes respond to changes or disturbances. Unlike steady state, where conditions remain constant, the dynamic state focuses on transitions and adjustments. Understanding dynamic processes is essential for designing efficient control systems and improving operational performance and safety.
Q5.
Proportional control action is:
A. Constant output
B. Proportional to error
C. Integration of error
D. Derivative of error
📘 View Explanation
Correct Answer:
B
Output is proportional to error magnitude.
Q6.
In a PI controller, "I" stands for:
A. Proportional
B. Integral
C. Interrupt
D. Initialization
📘 View Explanation
Correct Answer:
B
Integral term accumulates error over time.
Q7.
Derivative control action anticipates:
A. Current error
B. Future error
C. Past error
D. Setpoint value
📘 View Explanation
Correct Answer:
B
Derivative action predicts future error trends.
Q9.
Dead time in control system refers to:
A. Immediate response
B. Delay between input and output
C. No delay
D. Controller error
📘 View Explanation
Correct Answer:
B
Dead time is delay in system response.
Q11.
Feedforward control aims to:
A. Measure output only
B. Compensate for disturbances before effect
C. Ignore disturbances
D. Manual adjustments
📘 View Explanation
Correct Answer:
B
Feedforward anticipates disturbance effects.
Q12.
Reset windup occurs in:
A. Proportional control
B. Integrator in controller
C. Differentiator
D. Sensor noise
📘 View Explanation
Correct Answer:
B
Integrator saturation causes reset windup.
Q13.
The transfer function relates:
A. Input to output in frequency domain
B. Input to output in time domain
C. Setpoint to measurement
D. Error to manipulated variable
📘 View Explanation
Correct Answer:
A
Transfer function defines input-output relationship.
Q14.
In process control, hysteresis means:
A. No lag in response
B. Difference in output when input is increasing or decreasing
C. Instantaneous output change
D. Sensor failure
📘 View Explanation
Correct Answer:
B
Hysteresis is output difference depending on input direction.
Q15.
The steady-state error in a control system is:
A. Error at start
B. Error during dynamic response
C. Error after transient settles
D. No error
📘 View Explanation
Correct Answer:
C
Steady-state error is error after system settles.
Q18.
Which sensor measures flow rate?
A. Thermocouple
B. Flowmeter
C. Pressure gauge
D. Manometer
📘 View Explanation
Correct Answer:
B
Flowmeter measures flow rate.
Q20.
What does a PID controller use?
A. P only
B. P and I only
C. P, I, and D actions
D. I and D only
📘 View Explanation
Correct Answer:
C
PID uses proportional, integral and derivative actions.
Q21.
An advantage of feedforward control is:
A. Correction after error
B. Anticipates disturbances
C. Simple to implement
D. Requires no sensors
📘 View Explanation
Correct Answer:
B
Feedforward anticipates disturbances before effect.
Q22.
Which term describes system stability?
A. Oscillations increase
B. Output approaches setpoint over time
C. Output diverges
D. No control action
📘 View Explanation
Correct Answer:
B
Stable system reaches desired output.
Q23.
Process gain is:
A. Change in input per change in output
B. Ratio of output change to input change
C. Controller gain
D. Signal attenuation
📘 View Explanation
Correct Answer:
B
Process gain is output/input ratio.
Q24.
Tuning a PID controller involves adjusting:
A. Proportional, integral, derivative gains
B. Only proportional gain
C. Only integral gain
D. Only derivative gain
📘 View Explanation
Correct Answer:
A
PID tuning adjusts all three gains.
Q26.
In a control loop, actuator is:
A. Device receiving control action
B. Sensor
C. Controller output
D. Setpoint
📘 View Explanation
Correct Answer:
A
Actuator executes control output.
Q27.
What is the function of a transmitter?
A. Measures process variable
B. Controls valve
C. Transmits sensor signal
D. Manual input
📘 View Explanation
Correct Answer:
C
Transmitter sends sensor signals to controller.
Q29.
Integral time constant represents:
A. Time taken for integral action to equal proportional action
B. Time delay in system
C. Time for derivative action
D. Sampling interval
📘 View Explanation
Correct Answer:
A
Integral time controls integral action speed.
Q31.
Overshoot in control system is:
A. Peak surpassing setpoint
B. Slow rise in output
C. No steady state error
D. Delayed response
📘 View Explanation
Correct Answer:
A
Overshoot is exceeding the setpoint.
Q33.
Valve positioner is used to:
A. Control valve position precisely
B. Measure flow
C. Control temperature
D. Regulate pressure
📘 View Explanation
Correct Answer:
A
Positioner ensures accurate valve positioning.
Q35.
Proportional band is:
A. Range of error for full output change
B. Constant controller output
C. Time delay in controller
D. Noise filter
📘 View Explanation
Correct Answer:
A
Proportional band defines error range for controller output.